Deatschwerks offers a variety of fittings for custom fuel setup applications. Caps and plugs are used to end fuel flow, and to prevent a hose or component from spilling or leaking fuel. The caps and plugs are very simple and straight-forward to install, and should always have the gasket checked if necessary before re-use or maintenance.

This is a 6AN cap that can be threaded onto the end of male fittings and hose ends

Deatschwerks couplers have been produced to help deliver fuel from your tank to your engine with optimal performance and flow in mind. Non-restrictive, and manufactured to every applicable JIC and SAE standard, these couplers are constructed of heat-treated 6061 T-6 aluminum that is anodized in a titanium finish. The titanium finish compliments both OE and aftermarket engine bays and hides marks far better than standard black fittings. These high-grade materials and coatings are strong, light, and anti-corrosive for use in the most demanding fuel systems.

New o-rings and crush washers are recommended each time a fitting is reused. Sold in packs of 10. This is for 6AN fittings and couplers.

The proper selection of reliable hoses are integral to any fuel system. Deatschwerks makes a number of different braided hoses, covering most applications required for transferring fuel or other fluids. This line of Poly Tetra Fluoro Ethylene (PTFE) allow tighter radius bends, are lower weight and have zero fuel vapor permeability compared to CPE hoses. They are pressure rated up to 1000 psi in stainless steel and black nylon.

Part number 6-02-0864-3 is 3 ft of PTFE hose, AN-6 size with black nylon exterior. See spec sheet for further details and other Deatschwerks hose options.

The proper selection of reliable hoses are integral to any fuel system. Deatschwerks makes a number of different braided hoses, covering most applications required for transferring fuel or other fluids. This line of Poly Tetra Fluoro Ethylene (PTFE) allow tighter radius bends, are lower weight and have zero fuel vapor permeability compared to CPE hoses. They are pressure rated up to 1000 psi in stainless steel and black nylon.
Part number 6-02-0864-20 is 20 ft of PTFE hose, AN-6 size with black nylon exterior. See spec sheet for further details and other Deatschwerks hose options.

The proper selection of reliable hoses are integral to any fuel system. Deatschwerks makes a number of different braided hoses, covering most applications required for transferring fuel or other fluids. This line of Poly Tetra Fluoro Ethylene (PTFE) allow tighter radius bends, are lower weight and have zero fuel vapor permeability compared to CPE hoses. They are pressure rated up to 1000 psi in stainless steel and black nylon.
Part number 6-02-0864-10 is 10 ft of PTFE hose, AN-6 size with black nylon exterior. See spec sheet for further details and other Deatschwerks hose options.

The proper selection of reliable hoses are integral to any fuel system. Deatschwerks makes a number of different braided hoses, covering most applications required for transferring fuel or other fluids. This line of Chlorinated Polyethylene (CPE) hoses are lined for compatibility with ethanol-based fuels up to E85. They are also cord reinforced for high pressure up to 350 psi in black nylon.

Part number 6-02-0815-3 is 3 ft of CPE hose, AN-6 size with black nylon exterior. See spec sheet for further details and other Deatschwerks hose options.

DeatschWerks DW440 brushless in-tank electric fuel pumps have a total height of only 4 in., making them easy to retrofit into any OE pump module. Brushless technology reduces friction and heat, increases efficiency, vastly improves pump lifespan in ethanol and methanol fuels—and allows higher voltage inputs for increased flow! These pumps move 440 lph of fuel at 40 psi. Each fuel pump includes a controller, which accepts an 8-22 V DC input and creates a digital signal to allow precise speed and torque control. The controllers are available in three configurations: single speed, dual speed, and PWM-controlled. Controller are designed to be used with voltage boosters, and the pump kits also include bulkhead wiring.

Model Compatibility

• Ford Mustang 2011-2014
• Ford F-150 2011-2014

DeatschWerks DW440 brushless in-tank electric fuel pumps have a total height of only 4 in., making them easy to retrofit into any OE pump module. Brushless technology reduces friction and heat, increases efficiency, vastly improves pump lifespan in ethanol and methanol fuels—and allows higher voltage inputs for increased flow! These pumps move 440 lph of fuel at 40 psi. Each fuel pump includes a controller, which accepts an 8-22 V DC input and creates a digital signal to allow precise speed and torque control. The controllers are available in three configurations: single speed, dual speed, and PWM-controlled. Controller are designed to be used with voltage boosters, and the pump kits also include bulkhead wiring.

Model Compatibility

• Subaru WRX 2008-2014
• Subaru STI 2008 +