The Planted Seat Bracket is a vehicle specific bracket used as an adapter between the floor of the vehicle and an aftermarket seat and it’s accessories. Because the floor of each vehicle varies and typically is not flat, a vehicle specific seat bracket is required for installing an aftermarket seat. Planted create each seat bracket using the floor of the vehicle as a reference. They bring each vehicle into their development center so they can create the best fitting, bolt-in, universal seat bracket possible. This allows aftermarket seats not only to be bolt-in without drilling, but also fully reversible back to stock if necessary.

Planted Seat Brackets are laser cut from 3/16 inch thick steel and hand welded to ensure weld penetration for superior strength. Each bracket is pre-slotted with hole patterns to accept sliders from most major seat manufacturers. There is extra space on the bracket for drilling your own hole pattern if using a slider with a less common hole pattern, or direct mounting a seat or side mount when eliminating sliders is preferred. They are finished with a black powder coat.

Disclaimers

• Seats come in many different shapes and sizes so not all seats will fit in all vehicles. It is up to the end user to determine if the seat will fit prior to ordering Planted adapter brackets and other components.
• Many vehicles have the steering wheel offset toward the center of the vehicle. This can be accentuated when installing an aftermarket seat of a different size then the factory seat.
• Replacing a factory seat with an aftermarket seat may cause the vehicle’s warning indicators to activate. This can be due to airbag, weight and/or other sensors in the factory seat that are not included in an aftermarket seat. It may be possible to eliminate these indicators with an electronic resistor but it is up to the end user to determine if a resistor will work & which resistor to use.
• Professional installation is recommended.

The Planted Seat Bracket is a vehicle specific bracket used as an adapter between the floor of the vehicle and an aftermarket seat and it’s accessories. Because the floor of each vehicle varies and typically is not flat, a vehicle specific seat bracket is required for installing an aftermarket seat. Planted create each seat bracket using the floor of the vehicle as a reference. They bring each vehicle into their development center so they can create the best fitting, bolt-in, universal seat bracket possible. This allows aftermarket seats not only to be bolt-in without drilling, but also fully reversible back to stock if necessary.

Planted Seat Brackets are laser cut from 3/16 inch thick steel and hand welded to ensure weld penetration for superior strength. Each bracket is pre-slotted with hole patterns to accept sliders from most major seat manufacturers. There is extra space on the bracket for drilling your own hole pattern if using a slider with a less common hole pattern, or direct mounting a seat or side mount when eliminating sliders is preferred. They are finished with a black powder coat.

Disclaimers

• Seats come in many different shapes and sizes so not all seats will fit in all vehicles. It is up to the end user to determine if the seat will fit prior to ordering Planted adapter brackets and other components.
• Many vehicles have the steering wheel offset toward the center of the vehicle. This can be accentuated when installing an aftermarket seat of a different size then the factory seat.
• Replacing a factory seat with an aftermarket seat may cause the vehicle’s warning indicators to activate. This can be due to airbag, weight and/or other sensors in the factory seat that are not included in an aftermarket seat. It may be possible to eliminate these indicators with an electronic resistor but it is up to the end user to determine if a resistor will work & which resistor to use.
• Professional installation is recommended.

Bell’s rear spoilers are designed to help improve the overall aerodynamic performance of the helmet. The V6 is a large air spoiler designed to be adapted to a wide range of Bell models. The spoiler is available in clear and attaches with aggressive double sided adhesive. An optional rear spoiler wicker that can be attached. Bell spoilers can be custom painted but Bell recommends using the adhesive to attach the spoiler to the helmet

For demanding environments, Bell makes .25mm thick tear-offs designed exclusively for Bell Helmets. Each sleeve comes with 10 individual tear-offs. Fits Bell helmets with the 287 SRV or SRV-8 shields, including the M.8, M.8 Carbon Dominator.2, GTX.2, Star Infusion, K.1 Pro, GP.2, and GP.2 Youth helmets.